🚗 Upgrade your Corvette’s edge with style and substance!
ECOTRIC Side Skirts are precision-engineered ABS plastic extensions designed specifically for 2014-2019 Corvette C7 coupe models. Featuring a glossy Carbon Flash Metallic finish, these lightweight rocker panels offer a bolt-on installation with pre-drilled holes and included hardware, enhancing your car’s sporty aesthetics while providing durable, weather-resistant protection.
Auto Part Position | Front |
Installation Type | Bolt-On |
Automotive Fit Type | Vehicle Specific Fit |
Manufacturer | ECOTRIC |
Model | ET-485 |
Item Weight | 3.99 pounds |
Package Dimensions | 77.5 x 6 x 3.02 inches |
Country of Origin | China |
Item model number | ET-485 |
Manufacturer Part Number | ET-485 |
A**Z
I'd recommend
Perfect fitment as long as you know what your doing
S**E
Fit well
Fit well and made look great
H**O
The way to go for budget side skirts.
The product made my ride from mild to wild. I installed them myself with no help. Must have an extremely low profile floor jack, and lift pucks for the insulation. Also 1in. 3M double sided tape for mocking up which wasn’t provided. The instructions were a little misleading, use a drill bit the same size as the pre-drilled holes on the skirts and screw in the self tapping screws with a snubby screwdriver. Took me 30 minutes on each side to install, can be done quickly with a helper.
J**S
Replacements for damaged trim
Replacement trim for some I famaged
W**R
This is not a high-performance part
Cheap looking poor quality
D**K
Reduce or eliminate dirty road spray from inching up the side of your c7
Installation was fairly simple. Remove the existing screw just behind the front tire (there are several to look at, only one is the correct one) . I attached the front end first, but kept the screw loose. Then I went about half way back from the front, and attached that screw, being sure to press the panel right up to where it should be, before you attempt to install that screw. Then I went to the last screw, just in front of the rear tire. SCREWS ARE SELP TAPPING, NO NEED TO PREDRILL HOLES IN BODY. CAUTION: I DID NOT FINISH TIGHTENING EACH SCREW WITH THE POWER DRILL AS THAT COULD BE TOO MUCH FORCE, AND STRIP OUT THE HOLE YOU MAKE IN THE BODY PANEL. FINISH TIGHTENING WITH A PHILLIPS SCREW DRIVE, BY HAND. After these first 3 screws, the panel is now in place to install the rest of the screws. There is quite a distance between the 1st and second screws, so I added one addition screw half way between the first two. Really adds a classy look, and functionality to your c7. Sides of the c7 do not get as dirty after a drive....... sweet!
D**A
Looks good
Looks good, didn’t lift the car just had my son help me put it on, took about an hour and the self tapping screws helped out that were included in the pack.
M**F
Looks Awesome
The skirts were better than I was expecting. The color matched the existing rear spoiler perfectly, so looks factory. Watched a utube video for installation which was helpful. Bought 3M Automobile 2-sided tape (not included). Did the install in my driveway in a half hour without lifting the car. There is only 1 bolt that is used from the car, the rest are self taper screws that are included. Pre-drilled holes are a help, but added 1 additional screw toward the front under the fender side vent. I was a little apprehensive screwing holes into my Baby, but the hole are down in the rocker panel out of sight. To install you must start with the front bolt to then line up the rest of the skirt. Then push skirt into place, 2 sided tape holds it as you screw it in. Again utube video was worth a watch to avoid mistakes. Once installed, very solid and looks amazing. Sets my car apart from the other C7 Z51's. High recommended. I also added new front splitter to complete the look. 🇺🇸
TrustPilot
vor 1 Woche
vor 1 Monat