Omix-Ada | 12035.50 | Cup Holder, Dual | OE Reference: CH-1 | Fits 1984-1996 Jeep Cherokee XJ

Perfect addition for my Jeep. Previously had to mess with holding drinks between my legs or trying to shove them in between the seats and make sure they’re stable, but with these cup holders I don’t have to worry about that anymore. This will fit most drinks fine, for example a large drink from McDonald’s will fit snug and not move but anything larger or taller won’t fit or will tip over. I do wish the cup holders were deeper but for what it is and for the price it holds up just fine for me.

Installed in 1 minute on my 96 XJ. No issues - I do find it fits cans (12oz/16oz) really well, but larger things sometimes don't fit super happily. I think most people fix this by cutting the bottom out of it...but for me I usually have cans or smaller drinks. Works great for me!

Hey XJ owners; I’ve been using the window style cup holders but they played havoc on my tint. I just retinted and was looking for a better solution so I don’t mess up the tint again. I ordered this product. It looks pretty good and holds water bottles ok. But the holders can’t be deep because of the brake so it needs a modification. Get this, plus some self adhesive weather stripping to customize the grip you want and you’ll be very happy. I had left over 1/2” x 1/2” weather striping but cut it down to about 1/2” x 1/4”. It holds my cups tightly around corners and never spills. I’ll post a picture if I can.

Fits in jeep.. but it’s not deep and doesn’t fit cups well.. had spills several times and because of it..Won’t continue to use it.

I put this in my 1986 AMC Jeep Cherokee Pioneer, I love it!! There are no cup holders in the vehicle factory, so this is definitely an improvement and it fits perfectly. If you’re someone who likes to drive crazy and skkrttt skkrrttt maybe it’s not for you because it does make it difficult to utilize the E Brake. However you could cut out the middle portion as someone else in the reviews did, and you’d still be able to use the cup holders. You could even cut the outer edges off and make it thin enough to fit in the center console if you have lost your center console lid like I did. I like it though, it improves my life just how it is.

Takes up a ton of room in between the seats while blocking the majority of the E-brake. Like, to the point where it's nearly impossible to deploy the e-brake, because you can't get your entire hand around it when this is installed. It sits forward at an angle that is ridiculous, while claiming to take up a "small footprint", because the "TOP" part of it is small-ish.Reality? Look at your Cherokee, open the center glove box, look down -- the two black screws that are holding the plastic on either side of the "latch" that clicks and latches the center box closed? Those will match the "tabs" in the picture. Then the "drink holder" will sit forward EIGHT INCHES over your emergency break. You will have roughly 2-3 inches left of the actual break itself, including the "button" on the end which you have to press down a full 3/4" of an inch to actually release the handle to deploy the break.Congratulations, you have officially covered and semi-permanently blocked your ability to use your emergency break in, you know, emergencies.The good news is, this is very solid ABS plastic, so --- it won't break, even if left in the boiling hot sun, in the Jeep. So, if an emergency does happen --- don't even dream of being able to snap it off to reach that E-Brake.Oy-vey, this was NOT a well designed aftermarket....Trust me, remove the lid to your glove box, take it to your shop, dremel the drink holder size you want, seal the work with liquid TPE that matches, or hot melt (or re-cover the piece in liquid rubber, for all that if you want it to look new-ish) -- and have your own custom piece. Done.

It's a good product if you don't need a huge drink; coffee cups and soda cans work best. If you drive a stick shift, or work on your XJ often (if you own an XJ you surely work on it often), it can be difficult to engage the hand brake. The colour matched and it reuses the two screws that are already there, very simple to install. Overall, it's a lot better than nothing and that's something.

It installs just fine, it's good quality, but it's basically useless because it isn't very deep and doesn't fit my coffee mug. Holds a beer can, so...yay.